Thermodynamics of aqueous biopolymer solutions and fractionation of Dextran

Flory-Huggins interaction parameters and thermal diffusion coefficients were measured for aqueous biopolymer solutions. Dextran (a water soluble polysaccharide) and bovine serum albumin (BSA, a water soluble protein) were used for this study. The former polymer is representative for chain macromolecules and the latter is for globular macromolecules. The interaction parameters for the systems water/dextran and water/BSA were determined as a function of composition by means of vapor pressure measurements, using a combination of headspace sampling and gas chromatography (HS-GC). A new theoretical approach, accounting for chain connectivity and conformational variability, describes the observed dependencies quantitatively for the system water/dextran and qualitatively for the system water/BSA. The phase diagrams of the ternary systems water/methanol/dextran and water/dextran/BSA were determined via cloud point measurements and modeled by means of the direct minimization of the Gibbs energy using the information on the binary subsystems as input parameters. The thermal diffusion of dextran was studied for aqueous solutions in the temperature range 15 < T < 55 oC. The effects of the addition of urea were also studied. In the absence of urea, the Soret coefficient ST changes its sign as T is varied; it is positive for T > 45.0 oC, but negative for T < 45.0 oC. The positive sign of ST means that the dextran molecules migrate towards the cold side of the fluid; this behavior is typical for polymer solutions. While a negative sign indicates the macromolecules move toward the hot side; this behavior has so far not been observed with any other binary aqueous polymer solutions. The addition of urea to the aqueous solution of dextran increases ST and reduces the inversion temperature. For 2 M urea, the change in the sign of ST is observed at T = 29.7 oC. At higher temperature ST is always positive in the studied temperature range. To rationalize these observations it is assumed that the addition of urea opens hydrogen bonds, similar to that induced by an increase in temperature. For a future extension of the thermodynamic studies to the effects of poly-dispersity, dextran was fractionated by means of a recently developed technique called Continuous Spin Fractionation (CSF). The solvent/precipitant/polymer system used for the thermodynamic studies served as the basis for the fractionation of dextran The starting polymer had a weight average molar mass Mw = 11.1 kg/mol and a molecular non-uniformity U= Mw / Mn -1= 1.0. Seventy grams of dextran were fractionated using water as the solvent and methanol as the precipitant. Five fractionation steps yielded four samples with Mw values between 4.36 and 18.2 kg/mol and U values ranging from 0.28 to 0.48.

Functional dextran-based hydrogels

Dextran-based polymers are versatile hydrophilic materials, which can provide functionalized surfaces in various areas including biological and medical applications. Functional, responsive, dextran based hydrogels are crosslinked, dextran based polymers allowing the modulation of response towards external stimuli. The controlled modulation of hydrogel properties towards specific applications and the detailed characterization of the optical, mechanical, and chemical properties are of strong interest in science and further applications. Especially, the structural characteristics of swollen hydrogel matrices and the characterization of their variations upon environmental changes are challenging. Depending on their properties hydrogels are applied as actuators, biosensors, in drug delivery, tissue engineering, or for medical coatings. However, the field of possible applications still shows potential to be expanded. rnSurface attached hydrogel films with a thickness of several micrometers can serve as waveguiding matrix for leaky optical waveguide modes. On the basis of highly swelling and waveguiding dextran based hydrogel films an optical biosensor concept was developed. The synthesis of a dextran based hydrogel matrix, its functionalization to modulate its response towards external stimuli, and the characterization of the swollen hydrogel films were main interests within this biosensor project. A second focus was the optimization of the hydrogel characteristics for cell growth with the aim of creating scaffolds for bone regeneration. Matrix modification towards successful cell growth experiments with endothelial cells and osteoblasts was achieved.rnA photo crosslinkable, carboxymethylated dextran based hydrogel (PCMD) was synthesized and characterized in terms of swelling behaviour and structural properties. Further functionalization was carried out before and after crosslinking. This functionalization aimed towards external manipulation of the swelling degree and the charge of the hydrogel matrix important for biosensor experiments as well as for cell adhesion. The modulation of functionalized PCMD hydrogel responses to pH, ion concentration, electrochemical switching, or a magnetic force was investigated. rnThe PCMD hydrogel films were optically characterized by combining surface plasmon resonance (SPR) and optical waveguide mode spectroscopy (OWS). This technique allows a detailed analysis of the refractive index profile perpendicular to the substrate surface by applying the Wentzel Kramers Brillouin (WKB) approximation. rnIn order to perform biosensor experiments, analyte capturing units such as proteins or antibodies were covalently coupled to the crosslinked hydrogel backbone by applying active ester chemistry. Consequently, target analytes could be located inside the waveguiding matrix. By using labeled analytes, fluorescence enhancement was achieved by fluorescence excitation with the electromagnetic field in the center of the optical waveguide modes. The fluorescence excited by the evanescent electromagnetic field of the surface plasmon was 2 3 orders of magnitude lower. Furthermore, the signal to noise ratio was improved by the fluorescence excitation with leaky optical waveguide modes.rnThe applicability of the PCMD hydrogel sensor matrix for clinically relevant samples was proofed in a cooperation project for the detection of PSA in serum with long range surface plasmon spectroscopy (LRSP) and fluorescence excitation by LRSP (LR SPFS). rn

Assembly and characterization of supramolecular architectures for biosensor applications

The research has included the efforts in designing, assembling and structurally and functionally characterizing supramolecular biofunctional architectures for optical biosensing applications. In the first part of the study, a class of interfaces based on the biotin-NeutrAvidin binding matrix for the quantitative control of enzyme surface coverage and activity was developed. Genetically modified ß-lactamase was chosen as a model enzyme and attached to five different types of NeutrAvidin-functionalized chip surfaces through a biotinylated spacer. All matrices are suitable for achieving a controlled enzyme surface density. Data obtained by SPR are in excellent agreement with those derived from optical waveguide measurements. Among the various protein-binding strategies investigated in this study, it was found that stiffness and order between alkanethiol-based SAMs and PEGylated surfaces are very important. Matrix D based on a Nb2O5 coating showed a satisfactory regeneration possibility. The surface-immobilized enzymes were found to be stable and sufficiently active enough for a catalytic activity assay. Many factors, such as the steric crowding effect of surface-attached enzymes, the electrostatic interaction between the negatively charged substrate (Nitrocefin) and the polycationic PLL-g-PEG/PEG-Biotin polymer, mass transport effect, and enzyme orientation, are shown to influence the kinetic parameters of catalytic analysis. Furthermore, a home-built Surface Plasmon Resonance Spectrometer of SPR and a commercial miniature Fiber Optic Absorbance Spectrometer (FOAS), served as a combination set-up for affinity and catalytic biosensor, respectively. The parallel measurements offer the opportunity of on-line activity detection of surface attached enzymes. The immobilized enzyme does not have to be in contact with the catalytic biosensor. The SPR chip can easily be cleaned and used for recycling. Additionally, with regard to the application of FOAS, the integrated SPR technique allows for the quantitative control of the surface density of the enzyme, which is highly relevant for the enzymatic activity. Finally, the miniaturized portable FOAS devices can easily be combined as an add-on device with many other in situ interfacial detection techniques, such as optical waveguide lightmode spectroscopy (OWLS), the quartz crystal microbalance (QCM) measurements, or impedance spectroscopy (IS). Surface plasmon field-enhanced fluorescence spectroscopy (SPFS) allows for an absolute determination of intrinsic rate constants describing the true parameters that control interfacial hybridization. Thus it also allows for a study of the difference of the surface coupling influences between OMCVD gold particles and planar metal films presented in the second part. The multilayer growth process was found to proceed similarly to the way it occurs on planar metal substrates. In contrast to planar bulk metal surfaces, metal colloids exhibit a narrow UV-vis absorption band. This absorption band is observed if the incident photon frequency is resonant with the collective oscillation of the conduction electrons and is known as the localized surface plasmon resonance (LSPR). LSPR excitation results in extremely large molar extinction coefficients, which are due to a combination of both absorption and scattering. When considering metal-enhanced fluorescence we expect the absorption to cause quenching and the scattering to cause enhancement. Our further study will focus on the developing of a detection platform with larger gold particles, which will display a dominant scattering component and enhance the fluorescence signal. Furthermore, the results of sequence-specific detection of DNA hybridization based on OMCVD gold particles provide an excellent application potential for this kind of cheap, simple, and mild preparation protocol applied in this gold fabrication method. In the final chapter, SPFS was used for the in-depth characterizations of the conformational changes of commercial carboxymethyl dextran (CMD) substrate induced by pH and ionic strength variations were studied using surface plasmon resonance spectroscopy. The pH response of CMD is due to the changes in the electrostatics of the system between its protonated and deprotonated forms, while the ionic strength response is attributed from the charge screening effect of the cations that shield the charge of the carboxyl groups and prevent an efficient electrostatic repulsion. Additional studies were performed using SPFS with the aim of fluorophore labeling the carboxymethyl groups. CMD matrices showed typical pH and ionic strength responses, such as high pH and low ionic strength swelling. Furthermore, the effects of the surface charge and the crosslink density of the CMD matrix on the extent of stimuli responses were investigated. The swelling/collapse ratio decreased with decreasing surface concentration of the carboxyl groups and increasing crosslink density. The study of the CMD responses to external and internal variables will provide valuable background information for practical applications.

Knock down von Desmoglein 2 durch induzierbare Cre-spezifische Rekombination in der Maus

Desmosomen sind hoch organisierte adhäsive interzelluläre Verbindungen, die benachbarte Zellen durch Verankerung mit den Intermediärfilamenten des Zytoskeletts miteinander verknüpfen und so Zellen und Geweben Stabilität verleihen. Die Adhäsionsmoleküle der Desmosomen sind die desmosomalen Cadherine. Diese transmembranen Glykoproteine gehen im Interzellulärraum Verbindungen mit den desmosomalen Cadherinen der Nachbarzelle ein und sind im zytoplasmatischen Bereich Anheftungspunkte für weitere an der Desmosomenbildung beteiligte Proteine. Ziel dieser Arbeit war die Untersuchung der Rolle von Desmoglein 2 (Dsg 2), einem in allen Epithelien exprimierten desmosomalen Cadherin. Da der konstitutive knock out von Dsg 2 embryonal letal ist, wurde im Rahmen dieser Doktorarbeit eine transgene Maus generiert, in der die Reduktion von Dsg 2 temporär regulierbar war (konditionaler knock down). Dazu wurde der Mechanismus der RNA Interferenz genutzt, wodurch Sequenz-spezifische, post-transkriptionelle Regulation von Genen möglich ist. Unter Verwendung eines über Cre/lox-induzierbaren Vektors wurden transgene Mäuse generiert, welche nach Induktion Dsg 2 shRNA exprimieren, die in der Zelle in siRNA umgewandelt wird und zum Abbau der Dsg 2 mRNA führt. Durch Verpaarung der generierten Dsg 2 knock down Maus mit der über Tamoxifen induzierbaren Cre Deleter knock in Mauslinie Rosa26CreERT2 konnte deutliche Reduktion der Dsg 2 Proteinmenge in Leber, Darm und Herz erreicht werden. In Immunfärbungen der Leber wurde zudem eine reduzierte Desmosomenbildung durch Expression der Dsg 2 shRNA detektiert. Die für diese Versuche generierte und getestete Rosa26CreERT2 Mauslinie ermöglichte jedoch nicht in allen Zellen eines Gewebes die komplette Aktivierung der Cre Rekombinase und damit die Expression der shRNA. Dadurch entstanden mosaikartige Wildtyp/knock down-Gewebe, in denen noch ausreichend Desmosomen gebildet wurden, um die Gewebestabilität und -struktur zu erhalten. Für eine funktionale Untersuchung von Dsg 2 in Zusammenhang mit der chronisch entzündlichen Darmerkrankung Colitis ulcerosa wurden die Dsg 2 knock down Mäuse mit Darm-spezifischen, induzierbaren Cre Deleter Mäusen (VillinCreERT2) verpaart. Nach Aktivierung der Cre Rekombinase mittels Tamoxifen wurde in bitransgenen Tieren über Gabe von Azoxymethan (AOM) und Dextransodiumsulfat (DSS) Colitis ulcerosa induziert. Diese entzündliche Erkrankung des Darms ist mit der Induktion von Darmtumoren assoziiert. Bereits nach einmaliger Induktion mit AOM/DSS wurde in der ersten endoskopischen Untersuchung eine starke Entzündung des Darmgewebes und die Ausbildung von flächig wachsenden Tumoren in den Dsg 2 knock down Tieren hervorgerufen. Es ist anzunehmen, dass durch knock down von Dsg 2, und die damit verbundene verminderte Desmosomenbildung und Zelladhäsion, Infiltration von Bakterien durch die epitheliale Barriere des Darms möglich war, und so die Entzündungsreaktion in der Darmmukosa verstärkte. In Zusammenhang mit Verlust der epithelialen Festigkeit durch verringerte Zellkontakte kam es zur Hyperproliferation der Darmmukosa, die sich in Ausbildung von flächigen Tumoren äußerte. In weiteren Experimenten müssen nun die Tumore und das entzündete Gewebe der Colitis-induzierten Mäuse mittels Immunfluoreszenz untersucht werden, um Veränderungen in der Desmosomenformation in situ detektieren zu können. Des Weiteren sind Verpaarungen der Dsg 2 knock down Maus mit anderen Cre Rekombinase exprimierenden Mauslinien möglich, um den Einfluss von Dsg 2 auch in anderen Geweben, beispielsweise im Herzen, zu untersuchen. Die hier vorgelegte Arbeit zeigt also erstmalig den ursächlichen Zusammenhang zwischen Dsg 2 und dem Auftreten von Colitis-assoziierten Tumoren in einem konditionalen RNAi-vermittelten knock down Tiermodell. Die Etablierung dieser Maus ist somit das erste konditionale Mausmodell, welches die bei vielen Krebspatienten gefundenen flachzellig wachsenden Tumore in vivo rekapituliert. Vorausschauend kann man sagen, dass mit Hilfe des im Rahmen dieser Doktorarbeit entwickelten Tiermodells wichtige Erkenntnisses über die Pathologie von Darmtumoren erbracht werden können, die unser Verständnis der Colitis-induzierten Tumorentstehung verbessern.

New biosensor applications of surface plasmon and hydrogel optical waveguide spectroscopy

Rapid and sensitive detection of chemical and biological analytes becomes increasingly important in areas such as medical diagnostics, food control and environmental monitoring. Optical biosensors based on surface plasmon resonance (SPR) and optical waveguide spectroscopy have been extensively pushed forward in these fields. In this study, we combine SPR, surface plasmon-enhanced fluorescence spectroscopy (SPFS) and optical waveguide spectroscopy with hydrogel thin film for highly sensitive detection of molecular analytes.rnrnA novel biosensor based on SPFS which was advanced through the excitation of long range surface plasmons (LRSPs) is reported in this study. LRSPs are special surface plasmon waves propagating along thin metal films with orders of magnitude higher electromagnetic field intensity and lower damping than conventional SPs. Therefore, their excitation on the sensor surface provides further increased fluorescence signal. An inhibition immunoassay based on LRSP-enhanced fluorescence spectroscopy (LRSP-FS) was developed for the detection of aflatoxin M1 (AFM1) in milk. The biosensor allowed for the detection of AFM1 in milk at concentrations as low as 0.6 pg mL-1, which is about two orders of magnitude lower than the maximum AFM1 residue level in milk stipulated by the European Commission legislation.rnrnIn addition, LRSPs probe the medium adjacent to the metallic surface with more extended evanescent field than regular SPs. Therefore, three-dimensional binding matrices with up to micrometer thickness have been proposed for the immobilization of biomolecular recognition elements with large surface density that allows to exploit the whole evanescent field of LRSP. A photocrosslinkable carboxymethyl dextran (PCDM) hydrogel thin film is used as a binding matrix, and it is applied for the detection of free prostate specific antigen (f-PSA) based on the LRSP-FS and sandwich immunoassay. We show that this approach allows for the detection of f-PSA at low femto-molar range, which is approximately four orders of magnitude lower than that for direct detection of f-PSA based on the monitoring of binding-induced refractive index changes.rnrnHowever, a three dimensional hydrogel binding matrix with micrometer thickness can also serve as an optical waveguide. Based on the measurement of binding-induced refractive index changes, a hydrogel optical waveguide spectroscopy (HOWS) is reported for a label-free biosensor. This biosensor is implemented by using a SPR optical setup in which a carboxylated poly(N-isoproprylacrylamide) (PNIPAAm) hydrogel film is attached on a metallic surface and modified by protein catcher molecules. Compared to regular SPR biosensor with thiol self-assembled monolayer (SAM), HOWS provides an order of magnitude improved resolution in the refractive index measurements and enlarged binding capacity owing to its low damping and large swelling ratio, respectively. A model immunoassay experiment revealed that HOWS allowed detection of IgG molecules with a 10 pM limit of detection (LOD) that was five-fold lower than that achieved for SPR with thiol SAM. For the high capacity hydrogel matrix, the affinity binding was mass transport limited.rnrnThe mass transport of target molecules to the sensor surface can play as critical a role as the chemical reaction itself. In order to overcome the diffusion-limited mass transfer, magnetic iron oxide nanoparticles were employed. The magnetic nanoparticles (MNPs) can serve both as labels providing enhancement of the refractive index changes, and “vehicles” for rapidly delivering the analytes from sample solution to an SPR sensor surface with a gradient magnetic field. A model sandwich assay for the detection of β human chorionic gonadotropin (βhCG) has been utilized on a gold sensor surface with metallic diffraction grating structure supporting the excitation of SPs. Various detection formats including a) direct detection, b) sandwich assay, c) MNPs immunoassay without and d) with applied magnetic field were compared. The results show that the highly-sensitive MNPs immunoassay improves the LOD on the detection of βhCG by a factor of 5 orders of magnitude with respect to the direct detection.rn

Light-sensitive polymeric nanoparticles based on photo-cleavable chromophores

Der Fokus dieser Arbeit liegt in dem Design, der Synthese und der Charakterisierung neuartiger photosensitiver Mikrogele und Nanopartikel als potentielle Materialien für Beladungs- und Freisetzungsanwendungen. Zur Realisierung dieses Konzepts wurden verschiedene Ansätze untersucht.Es wurden neuartige niedermolekulare lichtspaltbare Vernetzermoleküle auf der Basis von o-Nitrobenzylderivaten synthetisiert, charakterisiert und zur Herstellung von photosensitiven PMMA und PHEMA Mikrogelen verwendet. Diese sind unter Bestrahlung in organischen Lösungsmitteln quellbar und zersetzbar. Durch die Einführung anionischer MAA Gruppen in solche PHEMA Mikrogele wurde dieses Konzept auf doppelt stimuliresponsive p(HEMA-co-MAA) Mikrogele erweitert. Hierbei wurde ein pH-abhängiges Quellbarkeitsprofil mit der lichtinduzierten Netzwerkspaltung in wässrigen Medien kombiniert. Diese duale Sensitivität zu zwei zueinander orthogonalen Reizen stellt ein vielversprechendes Konzept zur Kombination einer pH-abhängigen Beladung mit einer lichtinduzierten Freisetzung von funktionellen Substanzen dar. Desweiteren wurden PAAm Mikrogele entwickelt, welche sowohl eine Sensitivität gegenüber Enzymen als auch Licht aufweisen. Dieses Verhalten wurde durch die Verwendung von (meth-)acrylatfunktionalisierten Dextranen als polymere Vernetzungsmoleküle erreicht. Das entsprechende stimuliresponsive Profil basiert auf der enzymatischen Zersetzbarkeit der Polysaccharid-Hauptkette und der Anbindung der polymerisierbaren Vinyleinheiten an diese über photospaltbare Gruppen. Die gute Wasserlöslichkeit der Vernetzermoleküle stellt einen vielversprechenden Ansatz zur Beladung solcher Mikrogele mit funktionellen hydrophilen Substanzen bereits während der Partikelsynthese dar. Ein weiteres Konzept zur Beladung von Mikrogelen basiert auf der Verwendung von photolabilen Wirkstoff-Mikrogel Konjugaten. In einem ersten Schritt zur Realisierung solch eines Ansatzes wurde ein neuartiges Monomer entwickelt. Hierbei wurde Doxorubicin über eine lichtspaltbare Gruppe an eine polymerisierbare Methacrylatgruppe angebunden. Für die Freisetzung hydrophober Substanzen in wässrigen Medien wurden polymere Photolack-Nanopartikel entwickelt, welche sich unter Bestrahlung in Wasser zersetzen. Die lichtinduzierte Änderung der Hydrophobizität des Polymers ermöglichte die Freisetzung von Nilrot durch das Auflösen der partikulären Struktur. Ein interessanter Ansatz zur Verhinderung einer unkontrollierten Freisetzung funktioneller Substanzen aus Mikrogelen ist die Einführung einer stimuliresponsiven Schale. In diesem Kontext wurden Untersuchungen zur Bildung von nicht-stimulisensitiven Schalen um vorgefertigte Mikrogelkerne und zur Synthese von Hydrogelkernen in vorgefertigten polymeren Schalen (Nanokapseln) durchgeführt.

The role of dendritic cells (DC) in Friend retrovirus-induced immunosuppression and immunotherapeutic applications of functionalized nanoparticles

Friend murine leukemia Virus (FV) infection of immunocompetent mice is a well- established model to acquire further knowledge about viral immune suppression mechanisms, with the aim to develop therapeutics against retrovirus-induced diseases. Interestingly, BALB/c mice are infected by low doses of FV and die from FV-induced erythroleukemia, while C57/BL6 mice are infected by FV only at high viral dose, and remain persistently infected for their whole life. Due to the central role of dendritic cells (DC) in the induction of anti-viral responses, we asked for their functional role in the genotype-dependent sensitivity towards FV infection. In my PhD study I showed that bone marrow (BM)-derived DC differentiated from FV-infected BM cells obtained from FV-inoculated BALB/c (FV susceptible) and C57BL/6 (FV resistant) mice showed an increased endocytotic activity and lowered expression of MHCII and of costimulatory receptors as compared with non-infected control BMDC. FV-infected BMDC from either mouse strain were partially resistant towards stimulation-induced upregulation of MHCII and costimulators, and accordingly were poor T cell stimulators in vitro and in vivo. In addition, FV-infected BMDC displayed an altered expression profile of proinflammator cytokines and favoured Th2 polarization. Ongoing work is focussed on elucidating the functional role of proteins identified as differentially expressed in FV-infected DC in a genotype-dependent manner, which therefore may contribute to the differential course of FV infection in vivo in BALB/c versus C57BL/6 mice. So far, more than 300 proteins have been identified which are differently regulated in FV-infected vs. uninfected DC from both mouse strains. One of these proteins, S100A9, was strongly upregulated specifically in BMDC derived from FV-infected C57BL/6 BM cells. S100A9-/- mice were more sensitive towards inoculation with FV than corresponding wild type (WT) mice (both C57BL/6 background), which suggests a decisive role of this factor for anti-viral defense. In addition, FV-infected S100A9-/- BMDC showed lower motility than WT DC. The future work is aimed to further elucidate the functional importance of S100A9 for DC functions. To exploit the potential of DC for immunotherapeutic applications, in another project of this PhD study the usability of different types of functionalized nanoparticles

Development of a system measuring adhesion forces in powder collectives

Fine powders commonly have poor flowability and dispersibility due to interparticle adhesion that leads to formation of agglomerates. Knowing about adhesion in particle collectives is indispensable to gain a deeper fundamental understanding of particle behavior in powders. Especially in pharmaceutical industry a control of adhesion forces in powders is mandatory to improve the performance of inhalation products. Typically the size of inhalable particles is in the range of 1 - 5 µm. In this thesis, a new method was developed to measure adhesion forces of particles as an alternative to the established colloidal probe and centrifuge technique, which are both experimentally demanding, time consuming and of limited practical applicability. The new method is based on detachment of individual particles from a surface due to their inertia. The required acceleration in the order of 500 000 g is provided by a Hopkinson bar shock excitation system and measured via laser vibrometry. Particle detachment events are detected on-line by optical video microscopy. Subsequent automated data evaluation allows obtaining a statistical distribution of particle adhesion forces. To validate the new method, adhesion forces for ensembles of single polystyrene and silica microspheres on a polystyrene coated steel surface were measured under ambient conditions. It was possible to investigate more than 150 individual particles in one experiment and obtain adhesion values of particles in a diameter range of 3 - 13 µm. This enables a statistical evaluation while measuring effort and time are considerably lower compared to the established techniques. Measured adhesion forces of smaller particles agreed well with values from colloidal probe measurements and theoretical predictions. However, for the larger particles a stronger increase of adhesion with diameter was observed. This discrepancy might be induced by surface roughness and heterogeneity that influence small and large particles differently. By measuring adhesion forces of corrugated dextran particles with sizes down to 2 µm it was demonstrated that the Hopkinson bar method can be used to characterize more complex sample systems as well. Thus, the new device will be applicable to study a broad variety of different particle-surface combinations on a routine basis, including strongly cohesive powders like pharmaceutical drugs for inhalation.

Evaluation of polymeric nanocarriers for RNA delivery

Therapeutic RNAs, especially siRNAs, are a promising approach for treating diseases like cancer, neurodegenerative disorders and viral infections. Their application, however, is limited due to a lack of safe and efficient delivery systems. Nanosized carriers with the ability to either complex or entrap RNA species are a promising option. rn rn rnSuch a carrier has to meet a lot of requirements, some of which are even partly contradictive. Understanding and controlling the interplay between the different demands would advance a strategic design at an early stage of therapeutic development. rn rn This work is centered around a systematic evaluation of polyplexes, such carriers that are able to complex siRNA due to electrostatic interactions. Six structurally and chemically diverse candidates, poly-L-lysine brushes, block copolymers, cationic peptides, cationic lipids, nanohydrogels, and manganese oxide particles, were tested in a simultaneous fashion. The assays, mostly based on fluorescently labeled siRNA, ranged from the evaluation of polyplex formation and stability to in vitro parameters like cellular uptake and knockdown capability. The analysis from several perspectives offered insight into the interplay between the specifications of one polyplex. Assessing the different carriers under exactly the same experimental conditions also allowed conclusions about favourable traits and starting points for further optimization. This comparative approach also revealed weaknesses of some of the conventional protocols, which were therefore contrasted with alternative methods. In addition, in vitro knockdown assays were optimized and the impact of fluorescently labeled siRNA on knockdown efficiency was assessed. rn rn rn A second class of carriers, which share the ability to entrap siRNA inside their matrix, are briefly addressed. Nanocapsules, dextran particles and liposomes were assessed for basic features like siRNA encapsulation and knockdown capability. rn rn rn rn In an approach towards targeted delivery of RNA, liposomes were endowed with mitochondriotropic tags. Despite successful functionalization, no colocalization between the liposomal cargo and mitochondria was so far observed, which makes further optimization necessary.

Saccharide based nanocapsules - From monomer building blocks to improved capsules properties

In dieser Arbeit wurde der vielfältige Nutzen von Kohlenhydraten in Nanokapsel Systemen untersucht. Drei verschiedene Nanokapsel-Typen wurden durch Reaktion an der Grenzfläche von inversen Miniemulsionen hergestellt. Es wurde gezeigt, dass die Kohlenhydrate nach Modifizierung als Monomer an der Kapselbildung teilnehmen können, oder zur Erhöhung der Sensitivität eines verkapselten Kontrastmittels beitragen können. Im Folgenden werden die Ergebnisse der einzelnen Projekte zusammengefasst. Eine neuartige Grenzflächen-Synthese zur Herstellung von Nanokapseln wurde entwickelt und untersucht. Bei der Reaktion handelt es sich um eine Ruthenium katalysierte Olefin-Kreuzmetathese, welche für die Reaktion an der Grenzfläche angepasst wurde. Als wasserlösliches Macromonomer wurde Dextranacrylat synthetisiert. Der Reaktionspartner war ein öl-löslichen Phosphoester (Phenyldi(undec-10-en-1-yl)phosphat). Anhand von NMR-Spektren wurde gezeigt, dass die Kapselbildung auf Olefin Kreuzmetathese beruht. Im Vergleich zu konventionellen Estern haben Phosphorester eine weitere Möglichkeit zur chemischen Funktionalisierung. Dies wurde exemplarisch durch die Verwendung von fluoreszenzmarkierten Phosphoestern gezeigt. Die Markierung wurde verwendet, um die pH-induzierte Abbaubarkeit der Nanokapseln mittels Fluoreszenz-Korrelations-Spektroskopie zu beobachten. Ziel des zweiten Projekts war es, Nanostrukturen zu entwickeln, um Infektionen mit Antibiotika-resistenten Bakterien lokal zu behandeln. Dazu wurden mit Dextranmethacrylat vernetzte Poly(acrylamid) basierte Nanogele synthetisiert und Zinknitrat zugesetzt. Die Synthese der Nanogele wurde erweitert, um durch Vernetzung freier Alkoholgruppen mit Toluoldiisocyanat eine Kapselschale zu erhalten. Die Schalenbildung spiegelte sich in einer geringeren Quellbarkeit der Gel- Schale-Hybride wieder. Die erhaltenen Gel-Schale-Hybride waren in der Lage das Wachstum von zwei Methicillin-resistenten Bakterienstämmen (S. aureus) zu unterdrücken und verzögern. Die synthetisierten Hybridstrukturen könnten in der Beschichtung von Wundauflagen Verwendung finden, um bakterielle Infektionen lokal und direkt nach Ausbruch zu behandeln. Ziel des dritten Projektes war es, die wichtigen Parameter in der Herstellung von Nanokapseln mit hoher Kontrastmittel Sensitivität zu identifizieren. Relaxivität/Signalsensitivität des Kontrastmittels ist von großer Bedeutung für die Bildgebung mittels MRI, dies kann durch die Begrenzung der Mobilität des Kontrastmittels erreicht werden. Aufgrund seiner hohen Komplexstabilität und seiner klinischen Bedeutung wurde das Kontrastmittel Gadobutrol für die Verkapselung verwendet. Das Kontrastmittel wurde in Polyharnstoff-Kapseln eingeschlossen, die durch einen inversen Miniemulsion-Prozess hergestellt wurden. Um die Viskosität im Inneren der Nanokapsel zu erhöhen, wurden zusätzlich Saccharose, Dextran und Polyacrylsäure verkapselt. In Gegenwart von Saccharose konnte die Relaxivität verdoppelt werden. Dies gründet sich vermutlich auf einem Second-sphere Effekt der Saccharose, einer auf Wasserstoffbrückenbindungen beruhende Interaktion von Kontrastmittel und Saccharose.